Febco FE850 DCA Backflow Preventer 1 in. FPT | FE850-100 (2024)

• Febco FE850 Backflow Preventer
• Female Pipe Thread
• 1 inch Double Check Assembly

Features & Benefits of the Febco 850 DCA 1" Backflow Preventer

Febco MasterSeries 850 In-Line Design Double Check Valve Assemblies are designed to prevent the backflow of pollutants that are objectionable but not toxic, from entering into the potable water supply. They feature a bronze body and threaded ball valve end connections. Maximum Working Pressure: 175psi.

• All non-health hazard (nontoxic) connections including: irrigation systems; fire sprinkler systems; in-plant commercial and industrial plumbing.
• Double check assemblies are not approved for backflow prevention of any toxic substance (liquid; solid; or gas).
• A double check assembly consists of two spring-loaded check valves; shut-off valves on the inlet and discharge side of the check valves and small test co*cks. Check valves allow water to flow in one direction only.
• A 12 inch minimum clearance is recommended under the assembly.

Febco 850 DCA Product Details

• Maximum Working Pressure: 175 PSI (1200 KPa)
• Hydrostatic Test Pressure: 350 PSI (2400 KPa)
• Temperature Range: 32F to 140F (0C to 60C)
• End Connections: Threaded ANSI B2.1
• Valve Body: Bronze
• Elastomers: Silicone
• Springs: Stainless Steel

WARNING!

Irrigation systems supplied by domestic or private potable water systems are considered to be a potential pollution hazard to the water supply. These systems must include protection to prevent possible backflow of irrigation water into the potable water supply.

Federal law requires a proper backflow device to be installed on any watering system to prevent contamination of the supply; whether it be pump or city water. Check your local water authority for installation requirements & codes. In many rural areas; specific requirements for landscape irrigation systems may not be covered in local plumbing codes and/or enforcement may be limited. HOWEVER...limitation in local authority does not alter the basic requirement for protection of the potable water supply.

Related Articles For The Febco 850 DCA

• How to Replace A Bonnet and Poppet
• Types of Backflow Preventers
• Atmospheric Vacuum Breaker (AVB)
• Pressure Vacuum Breaker (PVB)
• Double Check Valve Assembly (DCVA)
• How To Winterizing Your Sprinkler System

Replacement Parts

• Double Check Assembly (DCA) Parts

Various Parts And Materials Of The Double Check Assembly Backflow Device

The double check assembly consists of two spring-loaded check valves and shut-off valves on the inlet and discharges side of the check valves and small test co*cks. The valve body consists of durable bronze material. The elastomers are made up of a strong silicone material while the spring is stainless steel. These parts can be easily replaced and Sprinkler Warehouse stocks a variety of these irrigation replacement parts.

Febco FE850 DCA Important Product Details:

• Maximum Working Pressure: 175 PSI
• Hydrostatic Test Pressure: 350 PSI
• Temperature Range: 32F to 140F
• Max Working Pressure: 175 PSI
• End Connections: Threaded ANSI B2.1

Popular Videos For Learning About Backflow Devices:

• Choosing a Backflow Preventer
• Winterizing Your PVB
• Insulated Backflow Bags

Learn How To Install A Double Check Valve Device Underground

Install a rectangular irrigation box in accordance with local code. Dig a hole and fill it with enough drain rock to provide a flat surface 18″ below grade. Cover the rock with landscaping mesh before setting the rectangular valve box in place. Hold in place by packing soil on two sides away from the inlet and outlet holes. Cut inlet and outlet holes in the valve box as needed. Dry fit the assembly, unions, hose bib tee, and all connecting pipe. Measure the interior length of the valve box between the inlet and outlet holes. Subtract the assembly length from the interior length and divide the result in half. This is the distance from the interior upstream side of the valve box to the first fitting.